It's Almost Impossible For A Tank Crew To Survive Being Hit With A Sabot Round

The sabot round is a type of ammunition used by tanks in armored combat. This non-explosive anti-tank round encases a projectile, enabling it to hit its target with precision and obliterate the enemy inside. When employing the sabot round, a tank crew stands minimal to no chance of survival, which is a key reason for its preference in warfare.

Inner workings of the Sabot round

The purpose of the sabot round is to provide a structure that fills the entire bore area between a sub-caliber flight projectile and its barrel. This is to provide a larger surface area for the propellant gasses to act against, rather than just on the actual projectile itself. The aerodynamics don't always mesh smoothly with the interior ballistic design, so the sabot helps the round reach high-muzzle velocity.

The sabot surrounds the projectile to stabilize it as it propels through the barrel. It separates once the projectile has left the muzzle, leaving the projectile to fly straight toward its target, typically at a speed of 3,500 MPH.

Often, the projectile is a uranium-depleted narrow metal rod that's capable of penetrating armor. Once it makes impact with the target, it explodes into a spray of metal fragments. It's so powerful that one soldier once described it as liquifying everything - and everyone - inside the tank or armored vehicle it makes contact with.

The cup and expanding cup sabot rounds

There are five different types of sabot rounds. The cup sabot supports the base of the projectile and offers structural support around the shaft. It's typically used in small arms ammunition, as well as smoothbore shotgun and muzzleloader projectiles.

The expanding cup sabot is similar to the cup round, in that it's used for rifled small arms. However, when fired, the centrifugal force from the rotation of the projectile causes the segments surrounding it to open up. This introduces more surface area to the surrounding air pressure, releasing it.

Other types of sabot rounds

The base sabot has a one-piece base that supports the bottom of the projectile, as well as separate pieces that surround the sides and center, breaking away once the round has been fired. This sabot is considered superior to the previous two, as it offers a cleaner and better sabot-projectile separation. However, it's more expensive to produce.

The spindle sabot is typically used in large caliber armor-piercing ammunition. It uses between two and four longitudinal rings with a center section that makes contact with the projectile. The front centers the projectile in the barrel and provides an air scoop to help with its separation from the sabot, while the rear seals the propellant gases with an obturator ring along the outside diameter.

Finally, the ring sabot uses the projectile's rear fins to center it, forming a single ring around the front with an obturator ring to seal the gases. This type of sabot was favored by the Soviet Union, as the steel from which it was constructed could withstand launch accelerations without needing a ramp to support the projectiles.

Multiple generations of sabot round munitions

The M829A1, known as the "Silver Bullet," is an armor-piercing fin-stabilized discarding sabot (APFSDS) round. It has a long-rod, uranium-depleted projectile that's about 1.25 inches wide. Once it hits its target, it punches through armor and typically explodes an enemy tank in what tankers call a "jack in the box" effect.

According to Sofrep , the M829A1 "is widely regarded as the most effective tank-fired (M1 Abrams 120mm main gun) anti-armor weapons in the world. It overwhelmed Iraqi armor during Operation Desert Storm. The M829A1 is a depleted-uranium long-rod kinetic energy penetrator round capable of defeating heavily armored vehicles."

Since then, multiple generations of the round have been developed. The M829A2 improved the structural quality of the uranium-depleted projectile, while the M829A3 made the propellant more efficient to boost muzzle velocity. The M829A4 uses a uranium-depleted projectile with a three-petal composite sabot.

Use during Operation Desert Storm

Want War History Online 's content sent directly to your inbox? Sign up for our newsletter here!

The M1A2 Abrams tank was used throughout Operation Desert Storm and fired 120 mm M829 sabot rounds at enemy armored vehicles; the projectiles took out multiple tanks as they dominated the battlefield. M829 sabot rounds are best used in armored warfare, rather than toward buildings or walls, so were thoroughly employed by the US military throughout the Gulf War.